Superhydrophobic magnetic sorbent via surface modification of banded iron formation for oily water treatment

Jul 30, 2023

Scientific Reports volume 12, Article number: 11016 (2022) Cite this article

1140 Accesses

5 Citations

Metrics details

In the current study, a simple dry coating method was utilized to fabricate a super-hydrophobic super-magnetic powder (ZS@BIF) for oily water purification using zinc stearate (ZS) and banded iron formation (BIF). The produced composite was fully characterized as a magnetic sorbent for oily water treatment. The results of X-ray diffraction diffractometer (XRD), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS) and particle size analysis revealed the fabrication of homogenous hydrophobic-magnetic composite particles with core–shell structure. Contact angle and magnetic susceptibility results showed that 4 (BIF): 1 (Zs) was the ideal coverage ratio to render the core material superhydrophobic and preserve its ferromagnetic nature. The capability of the fabricated composite to sorb. n-butyl acetate, kerosene, and cyclohexane from oil–water system was evaluated. ZS@BIF composite showed a higher affinity to adsorb cyclohexane than n-butyl acetate and kerosene with a maximum adsorption capacity of about 22 g g−1 and 99.9% removal efficiency. Moreover, about 95% of the adsorbed oils could be successfully recovered (desorbed) by rotary evaporator and the regenerated ZS@BIF composite showed high recyclability over ten repeated cycles.

Oil spills occurred due to natural disasters, human activities, or industrial mistakes, damage water resources and cause high environmental risks. This kind of pollution attracted the attention of the research community to develop several procedures for pollution control and oil spill recovery1,2,3,4. For instance, when oil spills formed, a thin layer of oil covers a high area of water surface, which destroys marine life5. Besides, oil spill control and recovery are costly and many cleaning techniques do not permit complete oil recovery from water5. Various oil/water separation routes include booms, skimmers, sorbents, dispersants, in situ burning, bioremediation, and magnetic nanocomposites6,7,8,9. The new trends in oil/water separation consider some essential points including surface wettability (hydrophobicity degree), porosity, and roughness of numerous filtration/absorption surfaces. The separation materials with modified surfaces are usually fabricated in different shapes such as meshes10,11, textiles12,13,14, foams15,16, sponges17,18,19, films20, and membranes21. Honestly, most of the employed materials in the previous methods such as polypropylene, hydrazine hydrate, and graphene oxide are synthetic, expensive, harmful, and hard to biodegrade22. Recently, huge efforts have been paid to nature-derived materials such as marine sponges modified with vegetable waxes23 to eliminate some of these drawbacks. In addition, the combination of such hydrophobic surfaces with magnetic materials has attracted much attention due to the facile and fast collection of the oil-loaded materials from the aqueous medium at the end of the separation step. In this regard, magnetite nanoparticles coated with silica and (3-aminopropyl)triethoxysilane (APTS) illustrated a high efficiency for oily water treatment24. In addition, magnetite nanoparticles coated with cheap polyvinylpyrrolidone (PVP) prepared using a modified polyol method were used for the oil separation from water25.

On the other hand, recently, superhydrophobic sorbents have received more consideration in many applications, and the majority of surface modification methods suffer from many drawbacks26. These drawbacks include complex fabrication methods, weak stability in a severe environment, high energy consumption, and low adaptability27. Accordingly, the demand for fabricating new superhydrophobic sorbents with strong stability, simple production procedure, and high adaptability is urgent right now. Recently, zinc stearate28 and magnesium stearate29 have been utilized to coat sponges for oil/water treatment. Moreover, zinc stearate coated polyurethane sponges illustrated an adsorption capacity range of 6–81 g g−1 depending on the density of the sponge. Seth et al.30 coated cotton fabric with zirconium zinc stearate, which was highly efficient for oil/water separation. Tao et al.31 soaked a magnetic polyurethane sponge in a stearic acid solution to generate superhydrophobic characteristics, which was able to absorb oil from water with an absorption capacity of 16–60 g g−1. Previously, Tran and Lee32 treated polyurethane sponge with zinc oxide, stearic acid, and iron oxide to produce a superhydrophobic magnetic sponge applicable for oil/water separation. Xia et al.33 prepared a new magnetic foam from iron/iron carbide nanoparticles (Fe/Fe3C NPs) and polydimethylsiloxane (PDMS) coating, via ferric nitrate assisted chemical blowing and carbonization of polyvinylpyrrolidone (PVP). This developed showed high selectivity towards oil removal from water in non-open channels under assistance of a magnet. Polyurethane sponge loaded with magnetite nanoparticles also showed good superhydrophobic character for de-emulsification of toluene/water emulsions with excellent stability against sever acidic, basic, saline, cold and hot conditions34. Recently, natural iron oxide minerals have been used as a source of magnetism to develop magnetic sorbents for wastewater treatment applications35,36.

The present work is devoted to developing superhydrophobic magnetic composite via a simple-preparation technique called the dry coating process. It is summarized by using a magnetic iron ore such as banded iron formation (BIF) ore for the first time that can be hydrophobized with zinc stearate, which could be considered a cheap and efficient sorbent in oil spills removal due to its hydrophobicity and magnetic approachability.

A representative banded iron formation (BIF) was collected from the Wadi Karim and Um Anab areas in the central Eastern Desert, the Red Sea region of Egypt. At the lab, the ore was crushed, ground, mixed, split into smaller portions, and sealed for later usage.

Cyclohexane (C6H12) with 99% purity, Kerosene of pure chemical grade, n-butyl acetate (CH3·COO·(CH2)3·CH3) with 98.5 purity, and zinc stearate (ZS) powder with 99.5% purity used in this study were supplied from El-Nasr Chemical Company.

The representative sample of Egyptian Red Sea iron oxide ore (BIF) was utilized as the magnetic core for the sorbent material. The iron oxide content is about 70% with an average particle size of about 10 µm. The chemical grade zinc stearate (ZS) powder of 2 µm average particle size was implemented as a hydrophobic material. The samples of superhydrophobic magnetic sorbent (ZS@BIF) were prepared by loading two different amounts of ZS (1 and 5 g) on the surface of BIF particles achieving 5% and 20% weight ratio of ZS addition. The homogeneous mixing of both components was primarily carried out in the Ordered Mixture (O.M.) Dizer unit for 10 min. Each mixture was then moved to the hybridizer system Supplementary Fig. S1 (supplementary materials) (Nara Machinery Co. Ltd., Model: NHS-0, Tokyo, Japan). The coating of BIF particles was performed with the aid of Van der Waals forces as a result of the difference in the particle size. The high-speed rotation (12,000 rpm) operated through compressed air stream pumps leads to the generation of friction forces which causes the attraction of small particles on the surface of large ones forming a hydrophobic shell of ZS on the BIF core particles. The obtained magnetic sorbent samples ZS@BIF with two ZS contents (5% and 20%) were collected within 15 min of coting time.

The mineralogical composition of the iron ore sample and zinc stearate@banded iron formation composite (ZS@BIF) was characterized qualitatively using an X-ray diffraction diffractometer (Bruker D8 XRD). Fourier transform infrared (FTIR) (Spectrometer JASCO, 6300, Japan) was used for surface examination. The surfaces of the banded iron formation host and the fabricated composite ZS@BIF were deeply analyzed by X-ray photoelectron spectroscopy (XPS) using K-alpha Thermo Scientific AXIS 165 (Thermo Fisher Scientific, USA) spectrometer. The adsorption characteristics of n. butyl acetate (BA) and cyclohexane (CH) on ZS@BIF composites were evaluated using FTIR. The surface morphology investigations were performed using a scanning electron microscope (SEM), and the elemental mapping of zinc, iron and oxygen was observed by conducting Energy Dispersive X-Ray Spectroscopy EDS. Grain size analysis was conducted by laser particle size analyzer (BT-2001). Thermo Scientific Automatic pycnometer Pycnomatic ATC was used for density measurement.

To investigate the hydrophobicity strength of the samples, the wettability of BIF and ZS@BIF composites with 5% and 20% ZS was estimated with JC2000A contact angle apparatus using the free sessile drop method. The smooth surface of the sample powder was prepared on a glass plate for the estimation of the contact angle. Then, a stable water droplet of about 1 mm diameter was placed on the sample surface using a microsyringe.

High-resolution magnetic susceptibility readings from powder samples including BIF, 5% ZS@BIF, and 20% ZS@BIF were measured to evaluate their magnetic properties using MS2G meter manufactured by Bartington Instruments, Oxford, England. MS2G is designed for magnetic susceptibility measurements of powder samples.

The absorption capacities of BIF, 5% ZS@BIF, and 20% ZS@BIF composites powder were studied to show the capability of the composites for the efficient removal of different kinds of oils from water. A 0.5 g of composite powder is placed between two layers of cotton on a funnel, and the oily water containing a defined volume of kerosene, butyl acetate, or cyclohexane is allowed to flow through the composite powder to a conical flask. After complete and saturated adsorption, the volume of un-adsorbed oil was measured and then the adsorption capacity Q in g g−1 was calculated as follow:

where Ci is the initial mass of oil in g, Ce is the mass of oil at equilibrium, and m is the mass of composite in g.

The advantages of the magnetic and hydrophobic abilities of the superhydrophobic composites were investigated. The oil was poured on the water surface, then the composite particles were spread in the oil/water mixture, and oil is absorbed into the particles quickly forming the particles/oil layer. The particle/oil phase was then removed by applying an external magnetic field. In addition, a rotary evaporator was used to distill the adsorbed oil off and recover the adsorbent for multi-cycle reuse.

The XRD pattern results of BIF and ZS@BIF (20%ZS) are given in Fig. 1a,b, which indicate that the major minerals are magnetite (Fe3O4), hematite (Fe2O3), quartz (SiO2), and albite (NaAlSi3O8) in BIF, while ZS@BIF has the same mineralogy in addition to zinc stearate peaks with a slight shift in the XRD peaks to a lower angle.

(a) XRD patterns of banded iron formation (BIF) and zinc stearate@banded iron formation composite (ZS@BIF), (b) Shift of XRD peaks to lower angles. [Albite (A), Hematite (H), Magnetite (M), Quartz (Q), Zinc stearate (Z)].

The FTIR patterns of BIF and ZS@BIF composite are presented in Fig. 2. In the BIF spectrum, the observed peak at 3432 cm−1 is assigned to the vibration and stretching of hydroxyl bonds (OH) of the absorbed water37,38. The bands at 2851 cm−1 and 2920 cm−1 are ascribed to the asymmetric and symmetric C–H bonds39,40. The observed band at 1628 cm−1 in the BIF spectrum is attributed to the physically adsorbed H–O–H bonds. The two bands observed at 1089 cm−1 and 789 cm−1 are assigned to the bending vibrations of Si–O–Si bonds41. The two absorption bands at 554 cm−1 and 461 cm−1 are related to the F–O bond's bending mode existing in the two crystallines α-Fe2O3 and Fe3O442.

FTIR spectra of BIF and 20% ZS@BIF composite.

The characteristic peaks of zinc stearate were observed in the FTIR spectrum of ZS@BIF in addition to the observed peaks of BIF. In particular, the peaks of symmetric and antisymmetric COO– bands were observed at 1398 cm−1 and 1539 cm−1 respectively42. The peaks observed at 2919, 2852, and 1460 cm−1 are attributed to symmetric and antisymmetric H–C–H bonds42. Moreover, the characteristic peak of the Zn–O chelating bond could be observed at 1539 cm−142.

Fe2p, O1s high-resolution XPS spectra for BIF and ZS@BIF samples in addition to Zn2p and C1s spectra for ZS@BIF composite are shown in Fig. 3. As in Fig. 3a,b, the Fe2p spectra for both samples are identical where the two main peaks of Fe2p3/2 and Fe2p1/2 were positioned around 711 eV and 725 eV, respectively which is in agreement with those observed for hematite α-Fe2O3 and magnetite Fe3O4 phases confirming the results of XRD investigation40,41,42,43.

XPS spectra for BIF and ZS@BIF samples.

The O1s spectra for BIF and ZS@BIF are shown in Fig. 3c,d. For the BIF sample, the observed peaks at 529.1 and 530.6 eV are attributed to Fe–O bonds44, and the peak observed at 535.8 eV is due to the O–H bond of adsorbed water45,46. Conversely, in the O1s spectrum of ZS@BIF, as shown in Fig. 3d, the characteristic peak of Zn–O was observed at binding energy 531.5447 while the peak was observed at 538.48 eV may be attributed to the aliphatic C=O bond in zinc stearate48. It is noteworthy that the absence of O–H characterized peak of adsorbed water in O1s in the ZS@BIF sample is due to the superhydrophobic nature of its surface.

The observed peaks at 1022.6 and 1045.74 eV in the Zn2p spectrum shown in Fig. 3e correspond to the Zn 2p3/2 and Zn 2p1/2 in Zn–O, respectively47.

The C1S spectrum of the ZS@BIF sample is shown in Fig. 3f, in which the main core spectrum is divided into four multiplet peaks at 284.52, 285.22, 285.87, and 288.85 eV, which indicate the presence of C–H, C=C, and O=C–O/and or O–C–O functional groups of stearate49,50,51,52.

The SEM micrograph for BIF particles in Fig. 4a reveals quite spherical-like morphology with a grain size diameter of about 2–5 µm. High magnification SEM images are shown in Supplementary Figs. S2 and S3 (supplementary materials). Figure 4b,c shows the EDS spectrum and the corresponding elemental analysis of the BIF sample. The BIF sample contains about 49.18% Fe and 12.26% Si, which exactly matches the reported chemical analysis of BIF35,36.

SEM, EDS spectra, and chemical analysis of (a–c) BIF and (d–f) ZS@BIF and EDS elemental mapping images for 20% ZS@BIF sample (g).

On the other hand, the surface morphology of the 20% ZS@BIF sample displays spherical grains coated with very fine particles which have a cotton texture as shown in Fig. 4d. The EDS spectrum and elemental analysis of 20% ZS@BIF consist of 33.07% Fe, 11.95% Si, and 22.2% Zn as major constituents as depicted in Fig. 4e,f. Figure 4g represents the elemental mapping of the 20% ZS@BIF sample with different colors for the main elements. The observed image for Zn (green color) confirms the homogeneous distributions of zinc stearate over the particles of iron oxides which are characterized by blue and red colors for Fe and O respectively.

Particle size distribution of BIF, 5% ZS@BIF, and 20% ZS@BIF samples are displayed in Fig. 5. The dry coating process made significant changes in the BIF grain size distribution. Therefore, a slight shift in the average particle size (d50) was noticed. Apparently, the average particle size (d50) increased from 2.5 µm for the BIF to 2.8 µm for 5% ZS@BIF and 5.7 µm for 20% ZS@BIF. Likely, a dramatic increase was observed for the d90 value where it jumped from 5.1 to 8 µm and 16 µm for BIF, 5% ZS@BIF, and 20% ZS@BIF, correspondingly. The escalation in the grain size of the coated BIF samples confirms the formation of ZS@BIF composites.

Particle size analysis of BIF, 5% ZS@BIF, and 20% ZS@BIF sample.

Another indication for the particle size enlargement after the coating process could be observed from the results of density measurements as shown in Table 1. Coating the BIF with 5% zinc stearate could make a 10.4% decrease in the BIF density while a density decrease of 40.6% was obtained when the coverage percentage raised to 20%. The deviation of the measured densities from the calculated ones of ZS@BIF composites is attributed to the large numbers of voids (mainly air) attached to zinc striate because of its strong hydrophobic nature. These huge numbers of voids (30%) may enhance the capability of ZS@BIF composite to absorb a large amount of oily liquid.

The contact angles increased from 35° to 127° and 151° by raising the percentage of ZS from 0 to 5% and 20% respectively as shown in Fig. 6. Thus, using zinc stearate as a coating layer was successful in producing a superhydrophobic composite for oil/water separation. The oil wettability was tested on these superhydrophobic composites, and it was found that the oil contact angle was 0° approximately indicating that both 5% and 20% ZS@BIF composite surfaces have a strong affinity to adsorb oil confirming that they are super oleophilic.

Contact angles with a water droplet on BIF, 5% ZS@BIF, and 20% ZS@BIF.

The magnetic susceptibility describes the degree of magnetization of the composites in response to an applied magnetizing field. It can be noted that the magnetic susceptibility for ZS@BIF composites gradually decreased with increasing ZS percent as shown in Supplementary Fig. S4 (supplementary materials). Although the addition of 20%ZS causes a noticeable reduction in the magnetic susceptibility of BIF, the produced 20%ZS@BIF still keeps a strong ferromagnetic character. Thus, the oil/composites phase could be effectively separated by conducting an external magnetic field.

The adsorption capacities of superhydrophobic magnetic ZS@BIF composites for oil pollutants were studied to examine the oil/water separation performance as depicted in the recorded video V1 in the supplementary materials.

Figure 7 reveals the adsorption capacity of three different oil phases (cyclohexane, kerosene, and n. butyl acetate) per gram of BIF, 5% ZS@BIF, and 20% ZS@BIF composites. The adsorption capacity is highly related to the type of treated oil and the degree of hydrophobicity of the composites. 20% ZS@BIF exhibited the maximum adsorption capacity for cyclohexane of about 22 g g−1 (Fig. 7). This could be due to the very small relative polarity value of cyclohexane. The high efficiency of the ZS@BIF composites is mainly due to the high contact angle and strong magnetic capabilities.

The adsorption capacity of oil on ZS@BIF treated with different percentages of ZS to BIF composite.

Generally, the adsorption capacity of the newly developed 20% ZS@BIF composite exhibits moderate behavior in comparison with that of all magnetic hydrophobic composites previously reported in the literature for oil–water separation as described in Table 2.

It is worth mentioning that it is the first time to consider the magnetic nature of BIF ore to be employed as water-repellent and oil-adsorbing material as shown in Fig. 8a–d. Once the composite material was put in the oil/water mixture, oil was adsorbed quickly on the surface of composite particles forming the oil/particles layer. Then by applying an external magnetic field, the oil/particle layer was removed spontaneously to produce clean water. This test illustrated that the ZS@BIF composite material could be involved as a promising superhydrophobic/super oleophilic magnetic oil sorbent as shown in Fig. 8e.

Oil/water separation using ZS@BIF composite (a) oil layer above water, (b) adding superhydrophoic magnetic composite, (c) magnet approaching the oil/composite layer, and (d) oil/composite layer attracted to an external magnetic field, (e) Image before and after oil/water separation using ZS@BIF composite.

At the end of the oil/water separation experiments, the used hydrophobic magnetic sorbent ZS@BIF was collected by a hand magnet and after drying at room temperature, an FTIR investigation was conducted. As can be seen in Fig. 9, the characteristic peaks of cyclohexane, asymmetric and symmetric –CH2– stretching vibration bands at 2917 cm−1 and 2848 cm−1 respectively were observed63. The FTIR spectrum of ZS@BIF loaded with kerosene shows a typical shape of bands with pure kerosene. The sharp peaks observed at 2955 cm−1, 2922 cm−1, and 2853 cm−1 are ascribed to stretching the C–H alkanes group in kerosene64.

FTIR spectra of ZS@BIF composite loaded by kerosene and cyclohexane.

The amenability to recover the adsorbed oil (desorption) by rotary evaporator was examined as shown in the recorded Supplementary Video V2 (supplementary materials). First, the oil-loaded ZS@BIF was moved to the evaporating flask of the rotary evaporator, and then the temperature was set to + 10 °C over the boiling point of the studied oil for 15 min to achieve complete vaporization of the adsorbed oil and complete regeneration of the ZS@BIF sorbent. Results showed that for the studied oils, about 95% recoveries were achieved. Supplementary Fig. S5 in supplementary materials shows the oil-loaded ZS@BIF before and after the oil recovery experiment.

To estimate the durability and reusability of the developed superhydrophobic magnetic composite, the regenerated ZS@BIF sorbent was tested for 9 repetitive cycles reuse. Figure 10 depicts the adsorption capacity of the fabricated ZS@BIF sorbent for cyclohexane against the number of reuse cycles. The developed ZS@BIF sorbent revealed excellent performance and high efficiency for oil adsorption without significant change up to 10 cycles. Therefore, this type of low-cost and eco-friendly processing technique could be considered an effective technique for the fabrication of several natural composites as efficient oil adsorbents.

Adsorption performance of ZS@BIF composite for cyclohexane/water separation for 10 cycles.

Natural superhydrophobic magnetic sorbent (ZS@BIF) was successfully prepared via a one-step, low-cost, and simple hybridization technique. The structural investigation using XRD, SEM, and EDS confirmed the formation of the ZS@BIF composite. Elemental mapping of the ZS@BIF composite sample revealed the excellent and uniform dispersion of zinc stearate between the iron oxide particles. Surface wettability studies indicated that the water contact angles significantly increased from 35° for un-treated BIF to 151° for 20%ZS@BIF composite suggesting superior hydrophobicity for the fabricated novel magnetic sorbent. The prepared ZS@BIF showed the highest affinity to adsorb cyclohexane than n-butyl acetate and kerosene with a maximum adsorption capacity of about 22 g g−1. The fabricated ZS@BIF composite revealed an excellent performance with 99.9% removal efficiency and high recyclability over ten repeated cycles.

The datasets generated and/or analysed during the current study are not publicly available due to institutional roles and confidential conditions but are available from the corresponding author on reasonable request.

Jamsaz, A. & Goharshadi, E. K. An environmentally friendly superhydrophobic modified polyurethane sponge by seashell for the efficient oil/water separation. Process Saf. Environ. Prot. 139, 297–304 (2020).

Article CAS Google Scholar

Ma, W. et al. Biomimetic durable multifunctional self-cleaning nanofibrous membrane with outstanding oil/water separation, photodegradation of organic contaminants, and antibacterial performances. ACS Appl. Mater. Interfaces 12, 34999–35010 (2020).

Article CAS PubMed Google Scholar

Ma, W. et al. Nature-inspired chemistry toward hierarchical superhydrophobic, antibacterial and biocompatible nanofibrous membranes for effective UV-shielding, self-cleaning and oil–water separation. J. Hazard. Mater. 384, 121476 (2020).

Article CAS PubMed Google Scholar

Chen, F. et al. Table salt as a template to prepare reusable porous PVDF–MWCNT foam for separation of immiscible oils/organic solvents and corrosive aqueous solutions. Adv. Funct. Mater. 27, 1702926 (2017).

Article CAS Google Scholar

Singh, B., Kumar, S., Kishore, B. & Narayanan, T. N. Magnetic scaffolds in oil spill applications. Environ. Sci. Water Res. Technol. 6, 436–463 (2020).

Article CAS Google Scholar

Dave, D. & Ghaly, A. E. Remediation technologies for marine oil spills: A critical review and comparative analysis. Am. J. Environ. Sci. 7, 423–440 (2011).

Article CAS Google Scholar

Cumo, F., Gugliermetti, F. & Guidi, G. Best available techniques for oil spill containment and clean-up in the mediterranean sea. WIT Trans. Ecol. Environ. 103, 527–535 (2007).

Google Scholar

Albaigés, J. The basics of oil spill cleanup. 94, 1512–1514 (2014). https://doi.org/10.1080/03067319.2014.974591.

Guidi, G., Sliskovic, M., Violante, A. C. & Vukic, L. Best available techniques (BATs) for oil spill response in the Mediterranean Sea: Calm sea and presence of economic activities. Environ. Sci. Pollut. Res. Int. 23, 1944–1953 (2016).

Article PubMed Google Scholar

Yu, Y., Chen, H., Liu, Y., Craig, V. S. J. & Lai, Z. Selective separation of oil and water with mesh membranes by capillarity. Adv. Colloid Interface Sci. 235, 46–55 (2016).

Article CAS PubMed Google Scholar

Yu, J. et al. High-flux and robust Co3O4 mesh for efficient oil/water separation in harsh environment. ACS Omega 4, 7385–7390 (2019).

Article CAS PubMed PubMed Central Google Scholar

Lei, S. et al. Durable superhydrophobic cotton fabric for oil/water separation. Colloids Surf. A Physicochem. Eng. Asp. 533, 249–254 (2017).

Article CAS Google Scholar

Lv, N., Wang, X., Peng, S., Luo, L. & Zhou, R. Superhydrophobic/superoleophilic cotton-oil absorbent: Preparation and its application in oil/water separation. RSC Adv. 8, 30257–30264 (2018).

Article ADS CAS PubMed PubMed Central Google Scholar

Sharma, M., Singh, G. & Vaish, R. Diesel soot coated non-woven fabric for oil–water separation and adsorption applications. Sci. Rep. 9, 1–11 (2019).

ADS CAS Google Scholar

Patil, C. S. et al. Waste packaging polymeric foam for oil–water separation: An environmental remediation. Data Br. 19, 86–92 (2018).

Article Google Scholar

Udayakumar, K. V., Gore, P. M. & Kandasubramanian, B. Foamed materials for oil–water separation. Chem. Eng. J. Adv. 5, 100076 (2021).

Article Google Scholar

Ke, Q., Jin, Y., Jiang, P. & Yu, J. Oil/water separation performances of superhydrophobic and superoleophilic sponges. Langmuir 30, 13137–13142 (2014).

Article CAS PubMed Google Scholar

Wang, Z., Ma, H., Chu, B. & Hsiao, B. S. Super-hydrophobic polyurethane sponges for oil absorption. Sep. Sci. Technol. https://doi.org/10.1080/01496395.2016.124657052,221-227 (2016).

Article PubMed PubMed Central Google Scholar

Liang, L., Xue, Y., Wu, Q., Dong, Y. & Meng, X. Self-assembly modification of polyurethane sponge for application in oil/water separation. RSC Adv. 9, 40378–40387 (2019).

Article ADS CAS PubMed PubMed Central Google Scholar

Gondal, M. A. et al. Study of factors governing oil-water separation process using TiO2 films prepared by spray deposition of nanoparticle dispersions. ACS Appl. Mater. Interfaces 6, 13422–13429 (2014).

Article CAS PubMed Google Scholar

Wang, H. et al. Review: Porous metal filters and membranes for oil–water separation. Nanoscale Res. Lett. 13, 1–14 (2018).

Article ADS CAS Google Scholar

Yin, Z., Sun, X., Bao, M. & Li, Y. Construction of a hydrophobic magnetic aerogel based on chitosan for oil/water separation applications. Int. J. Biol. Macromol. 165, 1869–1880 (2020).

Article CAS PubMed Google Scholar

Wang, F., Lei, S., Ou, J., Li, C. & Li, W. Novel all-natural material for oil/water separation. Ind. Eng. Chem. Res. 58, 1924–1931 (2019).

Article CAS Google Scholar

Zhang, S. et al. Synthesis of quaternized chitosan-coated magnetic nanoparticles for oil–water separation. Mater. Lett. 191, 128–131 (2017).

Article CAS Google Scholar

Palchoudhury, S. & Lead, J. R. A facile and cost-effective method for separation of oil–water mixtures using polymer-coated iron oxide nanoparticles. Environ. Sci. Technol. 48, 14558–14563 (2014).

Article ADS CAS PubMed Google Scholar

Peng, M. et al. Synthesis and application of modified commercial sponges for oil–water separation. Chem. Eng. J. 373, 213–226 (2019).

Article CAS Google Scholar

Zhang, L., Li, L. & Dang, Z. M. Bio-inspired durable, superhydrophobic magnetic particles for oil/water separation. J. Colloid Interface Sci. 463, 266–271 (2016).

Article ADS CAS PubMed Google Scholar

Parsaie, A., Tamsilian, Y., Pordanjani, M. R., Abadshapoori, A. K. & McKay, G. Novel approach for rapid oil/water separation through superhydrophobic/superoleophilic zinc stearate coated polyurethane sponges. Colloids Surf. A Physicochem. Eng. Asp. 618, 126395 (2021).

Article CAS Google Scholar

Parsaie, A., Mohammadi-Khanaposhtani, M., Riazi, M. & Tamsilian, Y. Magnesium stearate-coated superhydrophobic sponge for oil/water separation: Synthesis, properties, application. Sep. Purif. Technol. 251, 117105 (2020).

Article CAS Google Scholar

Seth, M., Khan, H., Bhowmik, R., Karmakar, S. & Jana, S. Facile fabrication of fluorine free zirconium zinc stearate based superhydrophobic and superoleophilic coating on cotton fabric with superior antibacterial property. J. Sol Gel Sci. Technol. 94, 127–140 (2019).

Article CAS Google Scholar

Tao, C., Liu, H., Su, S., Xie, J. & Ma, Y. Preparation of superhydrophobic magnetic stearic acid polyurethane sponge for oil–water separation. J. Mater. Res. 35, 2925–2935 (2020).

Article ADS CAS Google Scholar

Tran, V.-H.T. & Lee, B.-K. Novel fabrication of a robust superhydrophobic PU@ZnO@Fe3O4 @SA sponge and its application in oil-water separations. Sci. Rep. 7, 1–12 (2017).

Article CAS Google Scholar

Xia, L. et al. Magnet-assisted selective oil removal from water in non-open channel and continuous oil spills clean-up. Sep. Purif. Technol. 282, 120119 (2022).

Article CAS Google Scholar

Yu, T. et al. Preparation of magnetic, superhydrophobic/superoleophilic polyurethane sponge: Separation of oil/water mixture and demulsification. Chem. Eng. J. 384, 123339 (2020).

Article CAS Google Scholar

Farahat, M. M., Sanad, M. M. S. & Abdel-khalek, M. A. Decoration of serpentine with iron ore as an efficient low-cost magnetic adsorbent for Cr (VI) removal from tannery wastewater. Powder Technol. 388, 51–62 (2021).

Article CAS Google Scholar

Sanad, M. M. S., Farahat, M. M. & Abdel Khalek, M. A. One-step processing of low-cost and superb natural magnetic adsorbent: Kinetics and thermodynamics investigation for dye removal from textile wastewater. Adv. Powder Technol. 32, 1573–1583 (2021).

Article CAS Google Scholar

Linh, N. L. M., Hoang Van, D., Duong, T., Tinh, M. X. & Khieu, D. Q. Adsorption of arsenate from aqueous solution onto modified vietnamese bentonite. Adv. Mater. Sci. Eng. 2019 (2019).

Aichour, A. & Zaghouane-Boudiaf, H. Synthesis and characterization of hybrid activated bentonite/alginate composite to improve its effective elimination of dyes stuff from wastewater. Appl. Water Sci. 10, 1–13 (2020).

Article ADS CAS Google Scholar

Feng, G. et al. Magnetic natural composite Fe3O4-chitosan@bentonite for removal of heavy metals from acid mine drainage. J. Colloid Interface Sci. 538, 132–141 (2019).

Article ADS CAS PubMed Google Scholar

Alekseeva, O. V., Rodionova, A. N., Noskov, A. V. & Agafonov, A. V. Bentonite/magnetite composite for removal of nitrofurazone. Clays Clay Miner. 67, 471–480 (2020).

Article ADS CAS Google Scholar

Suman, S. K. & Kumar, S. Reverse flotation studies on iron ore slime by the synergistic effect of cationic collectors. Sep. Sci. Technol. https://doi.org/10.1080/01496395.2019.160475755 (2019).

Article Google Scholar

Sanad, M. M. S., Farahat, M. M., El-Hout, S. I. & El-Sheikh, S. M. Preparation and characterization of magnetic photocatalyst from the banded iron formation for effective photodegradation of methylene blue under UV and visible illumination. J. Environ. Chem. Eng. 9, 105127 (2021).

Article CAS Google Scholar

Reaz, M., Haque, A. & Ghosh, K. Synthesis, characterization, and optimization of magnetoelectric BaTiO3–iron oxide core-shell nanoparticles. Nanomaterials 10, 563 (2020).

Article CAS PubMed Central Google Scholar

Cai, C. C. & Zhang, M. X. XPS analysis of carbon and oxygen in coking coal with different density intervals. In Applied Mechanics and Materials 347–350, 1239–1243 (Trans Tech Publications Ltd, 2013).

Chernyshova, I. V., Hochella, M. F. & Madden, A. S. Size-dependent structural transformations of hematite nanoparticles. 1. Phase transition. Phys. Chem. Chem. Phys. 9, 1736–1750 (2007).

Article CAS PubMed Google Scholar

Chamritski, I. & Burns, G. Infrared- and raman-active phonons of magnetite, maghemite, and hematite: A computer simulation and spectroscopic study. J. Phys. Chem. B 109, 4965–4968 (2005).

Article CAS PubMed Google Scholar

Gurav, A. B. et al. Superhydrophobic surface decorated with vertical ZnO nanorods modified by stearic acid. Ceram. Int. 40, 7151–7160 (2014).

Article CAS Google Scholar

Beamson, G. Briggs, D. High Resolution XPS of Organic Polymers, vol. 70 (Wiley, 1992).

Dar, M. I. & Shivashankar, S. A. Single crystalline magnetite, maghemite, and hematite nanoparticles with rich coercivity. RSC Adv. 4, 4105–4113 (2014).

Article ADS CAS Google Scholar

Jubb, A. M. & Allen, H. C. Vibrational spectroscopic characterization of hematite, maghemite, and magnetite thin films produced by vapor deposition. ACS Appl. Mater. Interfaces 2, 2804–2812 (2010).

Article CAS Google Scholar

Guo, Y. et al. One pot preparation of reduced graphene oxide (RGO) or Au (Ag) nanoparticle-RGO hybrids using chitosan as a reducing and stabilizing agent and their use in methanol electrooxidation. Carbon N. Y. 50, 2513–2523 (2012).

Article CAS Google Scholar

Zhang, Y., Zhang, N., Tang, Z. R. & Xu, Y. J. Graphene transforms wide band gap ZnS to a visible light photocatalyst. The new role of graphene as a macromolecular photosensitizer. ACS Nano 6, 9777–9789 (2012).

Article CAS PubMed Google Scholar

Jiang, Z. et al. Removal of oil from water using magnetic bicomponent composite nanofibers fabricated by electrospinning. Compos. Part B Eng. 77, 311–318 (2015).

Article CAS Google Scholar

Gu, H. et al. Magnetic nanocellulose-magnetite aerogel for easy oil adsorption. J. Colloid Interface Sci. 560, 849–856 (2020).

Article ADS CAS PubMed Google Scholar

Soliman, E. M., Ahmed, S. A. & Fadl, A. A. Adsorptive removal of oil spill from sea water surface using magnetic wood sawdust as a novel nano-composite synthesized via microwave approach 03 Chemical Sciences 0306 Physical Chemistry (incl. Structural). J. Environ. Health Sci. Eng. 18, 79–90 (2020).

Article CAS PubMed PubMed Central Google Scholar

Zhou, S., Jiang, W., Wang, T. & Lu, Y. Highly hydrophobic, compressible, and magnetic polystyrene/Fe3O4/graphene aerogel composite for oil–water separation. Ind. Eng. Chem. Res. 54, 5460–5467 (2015).

Article CAS Google Scholar

Dai, J. et al. 3D macroscopic superhydrophobic magnetic porous carbon aerogel converted from biorenewable popcorn for selective oil–water separation. Mater. Des. 139, 122–131 (2018).

Article CAS Google Scholar

Chin, S. F., Binti Romainor, A. N. & Pang, S. C. Fabrication of hydrophobic and magnetic cellulose aerogel with high oil absorption capacity. Mater. Lett. 115, 241–243 (2014).

Article CAS Google Scholar

Thanikaivelan, P., Narayanan, N. T., Pradhan, B. K. & Ajayan, P. M. Collagen based magnetic nanocomposites for oil removal applications. Sci. Rep. 2, 1–7 (2012).

Article CAS Google Scholar

da Costa, R. M. D. et al. Green polyurethane synthesis by emulsion technique: A magnetic composite for oil spill removal. Polímeros 27, 273–279 (2017).

Article Google Scholar

Jiang, P., Li, K., Chen, X., Dan, R. & Yu, Y. Magnetic and hydrophobic composite polyurethane sponge for oil–water separation. Appl. Sci. 10, 1453 (2020).

Article CAS Google Scholar

Gan, W. et al. Removal of oils from water surface via useful recyclable CoFe2O4/sawdust composites under magnetic field. Mater. Des. 98, 194–200 (2016).

Article CAS Google Scholar

Imtiaz, Q., Hosseini, D. & Müller, C. R. Review of oxygen carriers for chemical looping with oxygen uncoupling (CLOU): Thermodynamics, material development, and synthesis. Energy Technol. 1, 633–647 (2013).

Article CAS Google Scholar

Dollah, A. et al. Effects of ultrasonic waves during waterflooding for enhanced oil recovery. Int. J. Eng. Technol. 7, 232–236 (2018).

Article CAS Google Scholar

Download references

Open access funding provided by The Science, Technology & Innovation Funding Authority (STDF) in cooperation with The Egyptian Knowledge Bank (EKB).

Central Metallurgical Research and Development Institute, Helwan, 11421, Cairo, Egypt

Mohsen Farahat, Ahmed Sobhy & Moustafa M. S. Sanad

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

M.F.: Conceptualization, ore preparation, writing, methodology, investigation, writing, visualization, reviewing. A.S.: Conceptualization, ore preparation, writing, methodology, investigation, writing, visualization, reviewing. M.M.S.S.: Conceptualization, ore preparation, writing, methodology, investigation, writing, visualization, reviewing.

Correspondence to Mohsen Farahat.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary Video 1.

Supplementary Video 2.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Farahat, M., Sobhy, A. & Sanad, M.M.S. Superhydrophobic magnetic sorbent via surface modification of banded iron formation for oily water treatment. Sci Rep 12, 11016 (2022). https://doi.org/10.1038/s41598-022-15187-6

Download citation

Received: 03 April 2022

Accepted: 20 June 2022

Published: 30 June 2022

DOI: https://doi.org/10.1038/s41598-022-15187-6

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

Scientific Reports (2023)

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.